Phased verticals for 30m

-

    With the 3Y0J dxpedition on air, and 30m being used alot, I did what I could to get a qso. 

I have an inverted vee, fed with ladderline and a link tuner, which tunes on 30, but I wanted to try something a bit more directive.

Settled for 2 phased verticals which turned out nice.

Had 2 identical 6m fishing rods, which were extended using military surplus tent poles (Nato stuff). Had made a bunch of the ground plates at my last job, so it was a quick job throwing the antennas together. Used 2 elevated radial per vertical and used christmann phasing. The nano vna was very useful when cutting the feed and delay lines.

Here´s a link to  the VA7ST pahsing line calculator.

www.va7st.ca/christman phasing

Tests with a nearby station showed approx 10db stronger signal than compared to the vee. RBN spots showed around 6db in favour of the phased verticals over the vee. This antenna might be a keeper.


So, what about 3Y0J. No qso yet, but my hopes are still up.


//SA2CLC




Comments

Post a Comment

Popular posts from this blog

ARC-5 receiver power supply, an in depth look.

-
Image
 The power supply is essentially a vibrator power supply, but with an IC and mosfet instead of the mechanichal vibrator used in the old days. The schematic can be seen below: It´s actually quite straight forward:  The CD4047 is operated as an astable multivibrator, providing two , out of ohase, square waves, driving the gates of the FET´s. The FET´s ground one end of the transformer winding, causing current flow, and induces voltage to the secondary winding (which in this case in the old primary) Switching frequency is determined by capacitor C3 and resistor R4. These values in the schematic gives approx. 50Hz switching frequency.  Optional 28V operation: I included holes on the board to hold a zener diode at the input of the CD4047 (max vcc 18v) in case 28v operation would be used (non-modified filament strings). A different transformer is also needed. There is a transformer that fits the board, 14A-10R-36, by the number we can tell that it´s a centertapped 36v seco...
Read more

My HP8640 died!

-
Image
 My HP8640 died! This is me catching up on past projects. I did this back in 2022, figured someone would benefit from this information, since the 8640 is still around in great numbers at hams all over the globe. I bought a nice looking HP8640 at our local hamfest back in 2022. It was working when I got it home, but a day or two after I got it home, it started acting erratic, with RF ouput dropping out. eventually, there was no output whatsoever. Did some tests, and got to the conclusion that the cavity oscillator was not oscillating. Following various clues online, I tracked down the issue to the A3 unit (cavity), and a series resistor, which had drifted in value. By measuring the series resistance between the + feed and the A3Q1 socket and the - feed and the A3Q1 socket, I could see that the + lead seemed reasonable at 370ohms, whilst the - lead had drifted to 19Kohms, where I was expecting around 900ohms. The A3Q1 (HP21 pictured below) transistor sits under the small hex cap om t...
Read more

813 grounded grid amplifier

-
Image
2 x 813 grounded grid linear amplifier  This year marks 10 years since I built this amplifier, and it´s been in use on almost all QSO´s I´ve had since then.  When I got into amateur radio back in 2013/2014, I quite soon understood that I needed a vacuum tube amplifier. SB220´s and L4B´s were high on the wanted list, but there wasn´t anything for sale at that moment. I stumbled across a pair of 813´s and sockets, and that´s what set the wheels rolling. I begun by collecting the needed parts. High voltage transformer, variable caps, meters and such, and after that, it´s mostly a job of shaping metal and drilling holes. Most parts collected An aluminum chassis was bent using the sheet metal brake at work. Reinforcement extrusions was bolted to the underside of the chassis where the HV transformer would go. With a finished box a rough layout was determined, and the hole drilling excercise begun. Getting a feel of where to place things Lot of parts to fit. Note that pictured bandsw...
Read more